MARS - Mips Assembly and Runtime Simulator
Interactive Debugging Features
MARS provides many features for interactive debugging through its Execute pane.
- In Step mode, the next instruction to be simulated is highlighted and
memory content displays are updated at each step.
- Select the Go option if you want to simulate continually.
It can also be used to continue simulation
from a paused (step, breakpoint, pause) state.
- Breakpoints are easily set and reset using the check boxes next to each instruction displayed
in the Text Segment window. New in Release 3.8: You can temporarily suspend breakpoints
using Toggle Breakpoints in the Run menu or by clicking the "Bkpt" column header in the Text Segment
window. Repeat, to re-activate.
- When running in the Go mode, you can select the simulation
speed using the Run Speed slider. Available speeds range
from .05 instructions per second (20 seconds between steps) up to 30
instructions per second, then above this offers an "unlimited" speed.
When using "unlimited" speed, code highlighting and memory display updating
are turned off while simulating (but it executes really fast!).
When a breakpoint is reached, highlighting and updating occur.
Run speed can be adjusted while the program is running.
- When running in the Go mode, you can pause or stop
simulation at any time using the Pause or Stop features.
The former will pause execution and update the display, as if you
were stepping or at a breakpoint. The latter will terminate execution
and display final memory and register values. If running at "unlimited"
speed, the system may not respond immediately but it will respond.
- You have the ability to interactively step "backward" through program execution
one instruction at a time to "undo" execution steps. It will buffer up to 2000 of the most
recent execution steps (this limit is stored in a properties file and can be changed).
It will undo changes made to MIPS memory, registers or condition flags,
but not console or file I/O. This should be a great debugging aid.
It is available anytime execution is paused and at termination (even if terminated due to
- When program execution is paused or terminated, select Reset
to reset all memory cells and registers to their initial post-assembly values.
In fact, Reset is implemented by re-assembling the program.
- Memory addresses and values, and register values, can be viewed in either decimal
or hexadecimal format. All data are stored in little-endian byte order (each
word consists of byte 3 followed by byte 2 then 1 then 0). Note that each word
can hold 4 characters of a string and those 4 characters will appear in the
reverse order from that of the string literal.
- Data segment contents are displayed 512 bytes
at a time (with scrolling) starting with the data segment base address (0x10010000).
Navigation buttons are provided to change the display to the next
section of memory, the previous, or back to the initial (home) range. A combo box is
also provided to view memory contents in the vicinity of the stack pointer
(contents of MIPS $sp register), global pointer (contents of MIPS $gp register),
the heap base address (0x10040000), .extern globals (0x10000000),
the kernel data segment (0x90000000), or memory-mapped IO (MMIO, 0xFFFF0000).
- Contents of any data segment memory word and almost any MIPS register can be modified by
editing its displayed table cell. Double-click on a cell to edit it and press the Enter key
when finished typing the new value. If you
enter an invalid 32-bit integer, the word INVALID appears in the cell
and memory/register contents are not affected. Values can be entered
in either decimal or hexadecimal (leading "0x"). Negative hexadecimal
values can be entered in either two's complement or signed format. Note
that three of the integer registers (zero, program counter, return address)
cannot be edited.
- Contents of cells representing floating point registers can be edited
as described above and will accept valid hexadecimal or decimal floating point
values. Since each double-precision register overlays two single-precision
registers, any changes to a double-precision register will affect one or both
of the displayed contents of its corresponding single-precision registers.
Changes to a single-precision register will affect the display of its
corresponding double-precision register. Values entered in hexadecimal
need to conform to IEEE-754 format. Values entered in decimal are entered
using decimal points and E-notation (e.g. 12.5e3 is 12.5 times 10 cubed).
- Cell contents can be edited during program execution and once accepted
will apply starting with the next instruction to be executed.
- Clicking on a Labels window entry will cause the location associated with
that label to be centered and highlighted in the Text Segment or Data Segment
window as appropriate. Note the Labels window is not displayed by default but
can be by selecting it from the Settings menu.
This document is available for printing on the MARS home page